[[dt_openocd]]

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision
Previous revision
dt_openocd [2014/02/10 23:37]
yusa
dt_openocd [2014/06/27 09:35]
beckmanf added flyswatter usb configuration
Line 20: Line 20:
 <​code>​ <​code>​
 git clone git://​git.code.sf.net/​p/​openocd/​code openocd-code git clone git://​git.code.sf.net/​p/​openocd/​code openocd-code
 +</​code>​
 +
 +Install the libusb-1.0 package
 +
 +<​code>​
 +sudo apt-get install libusb-1.0-0-dev
 +./bootstrap
 +./configure --prefix=$HOME/​site
 +make
 +make install
 +</​code>​
 +
 +Add the file /​etc/​udev/​rules.d/​52-flyswatter.rules. This will make the usb device accessible without root permissions.
 +
 +<​code>​
 +# Flyswatter JTAG Debugger
 +SUBSYSTEMS=="​usb",​ ATTR{idVendor}=="​0403",​ ATTR{idProduct}=="​6010",​ MODE="​0666"​
 </​code>​ </​code>​
  
Line 36: Line 53:
 You can use openOCD with various hardware, so you have to tell openOCD which one you are actually using. This is done with some special Configuration Files. Overall you need three of these files: You can use openOCD with various hardware, so you have to tell openOCD which one you are actually using. This is done with some special Configuration Files. Overall you need three of these files:
  
- * interface config file descripes ​which hardware debugger you are using +  ​* interface config file: Descripes ​which hardware debugger you are using 
- * board config file descripes ​which kind of board you are using +  * board config file: Descripes ​which kind of board you are using 
- * target config files descripes ​which microcontroller you are using+  * target config files: Descripes ​which microcontroller you are using
  
 You can find a lot of configuration files for specific hardware there: You can find a lot of configuration files for specific hardware there:
Line 153: Line 170:
 reg [NAME] [VALUE] reg [NAME] [VALUE]
 </​code>​ </​code>​
 +
  
  
 === Debugging with gdb === === Debugging with gdb ===
  
-Follows soon...+If you want to debug your hardware more comfortable you are able to use gdb. 
 +You should use the gdb provided by your ToolchainFor example mipsel-none-elf-gdb for a MIPS architecture.
  
 +<​code>​
 +mipsel-none-elf-gdb main.elf
 +</​code>​
 +
 +
 +Connect to the gdbserver on the local pc using port 3333.
 +
 +<​code>​
 +(gdb) target remote localhost:​3333
 +</​code>​
 +
 +Send commands to gdbserver using the monitor command
 +
 +<​code>​
 +(gdb) monitor reset halt
 +</​code>​
 +
 +Now the hardware performs a reset and halts directly. You can use gdb as normal:
 +
 +You can list the source code:
 +
 +<​code>​
 +(gdb) list
 +</​code>​
 +
 +Set breakpoints (e.g. at line 27)
 +
 +<​code>​
 +(gdb) br 27
 +</​code>​
 +
 +Run the program until the next breakpoint occurs.
 +
 +<​code>​
 +(gdb) continue
 +</​code>​
 +
 +Walk step by step through your source code
 +
 +<​code>​
 +(gdb) next
 +</​code>​
 +
 +or print variable content
 +
 +<​code>​
 +(gdb) print [var]
 +</​code>​
  
  
  • dt_openocd.txt
  • Last modified: 2014/06/27 09:35
  • by beckmanf