Differences
This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision Last revision Both sides next revision | ||
searchwing-antenna-ground-box [2021/09/07 05:14] beckmanf Pololu |
searchwing-antenna-ground-box [2021/11/10 14:06] beckmanf add v2 link |
||
---|---|---|---|
Line 10: | Line 10: | ||
In addition it is possible to connect via the [[https://www.ftdichip.com/Support/Documents/DataSheets/Cables/DS_TTL-232R_CABLES.pdf|FTDI UART/USB]] cable with and without power from the 24V system. The router can also be connected with an ethernet cable to have wired access to the telemetry data. | In addition it is possible to connect via the [[https://www.ftdichip.com/Support/Documents/DataSheets/Cables/DS_TTL-232R_CABLES.pdf|FTDI UART/USB]] cable with and without power from the 24V system. The router can also be connected with an ethernet cable to have wired access to the telemetry data. | ||
+ | |||
+ | [[searchwing-antenna-ground-box#antenna_box_v2|Current Version V2]] | ||
+ | |||
+ | ==== Antenna Box V1 ==== | ||
{{ ::basestationplatine.png?600 |}} | {{ ::basestationplatine.png?600 |}} | ||
Line 79: | Line 83: | ||
The image shows the installed SearchWing Antenna Box on the Alan Kurdi. The box contains a Wifi Access Point for a connection to the flight tablet computer. It is therefore recommended to operate the tablet in proximity to the box. | The image shows the installed SearchWing Antenna Box on the Alan Kurdi. The box contains a Wifi Access Point for a connection to the flight tablet computer. It is therefore recommended to operate the tablet in proximity to the box. | ||
+ | ==== Antenna Box V2 ==== | ||
+ | |||
+ | A new PCB board integrates the voltage regulator, RFD868+ modem, UART to Ethernet Converter on one board. Everything is now installed via "Hutschiene". This version was installed on the [[https://www.hs-augsburg.de/searchwing/de/seawatch-tests-2021/|mission with Sea-Watch 4 with Philipp]]. | ||
=== Electronics / Board === | === Electronics / Board === | ||
- | Franc and Tim design a board for the antenna ground box. | + | Franc and Tim designed a board for the antenna ground box. |
+ | |||
+ | {{ ::sw-ags-pcb-v2.jpg |Antenna Ground Station PCB v1.0 with Hutschienenadapter}} | ||
+ | |||
+ | **Fig. 4:** Antenna Ground Station PCB v1.0 with Hutschienenadapter | ||
+ | |||
+ | Figure 4 shows the antenna ground box PCB version 1.0. The design data is available at | ||
+ | |||
+ | [[https://easyeda.com/SearchWing/antennagroundstation|Easyeda - Antenna Ground Station PCB Board]] | ||
+ | |||
+ | The pcb board is installed with Hutschiene inside the Spelsberg box. | ||
+ | |||
+ | {{ ::sw-ags-box-v2.jpg | Antenna Ground Station v2 with PCB and Hutschiene}} | ||
+ | |||
+ | **Fig. 5:** Antenna Ground Station v2 box with PCB and Hutschiene | ||
+ | |||
+ | Figure 5 shows the Antenna Ground Station box V2 with PCB and Wifi AP on Hutschiene. | ||
+ | |||
+ | {{ ::sw-ags-ap-hutschiene.jpg |}} | ||
- | [[https://easyeda.com/SearchWing/antennagroundstation||Easyeda - Antenna Ground Station Board]] | + | **Fig. 6:** Hutschienenadapter mit Sekundenkleber an Wifi AP geklebt |
+ | Figure 6 shows the Wifi Access Point glued with Sekundenkleber to the Hutschienenadapter. | ||