[[searchwing-antenna-ground-box]]

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Last revision Both sides next revision
searchwing-antenna-ground-box [2021/11/10 13:59]
beckmanf add AGS V2
searchwing-antenna-ground-box [2021/11/10 14:06]
beckmanf add v2 link
Line 10: Line 10:
  
 In addition it is possible to connect via the [[https://​www.ftdichip.com/​Support/​Documents/​DataSheets/​Cables/​DS_TTL-232R_CABLES.pdf|FTDI UART/USB]] cable with and without power from the 24V system. The router can also be connected with an ethernet cable to have wired access to the telemetry data. In addition it is possible to connect via the [[https://​www.ftdichip.com/​Support/​Documents/​DataSheets/​Cables/​DS_TTL-232R_CABLES.pdf|FTDI UART/USB]] cable with and without power from the 24V system. The router can also be connected with an ethernet cable to have wired access to the telemetry data.
 +
 +[[searchwing-antenna-ground-box#​antenna_box_v2|Current Version V2]]
 +
 +==== Antenna Box V1 ====
  
 {{ ::​basestationplatine.png?​600 |}} {{ ::​basestationplatine.png?​600 |}}
Line 81: Line 85:
 ==== Antenna Box V2 ==== ==== Antenna Box V2 ====
  
-A new PCB board integrates the voltage regulator, RFD868+ modem, UART to Ethernet Converter on one board. Everything is now installed via "​Hutschiene"​.+A new PCB board integrates the voltage regulator, RFD868+ modem, UART to Ethernet Converter on one board. Everything is now installed via "​Hutschiene"​. This version was installed on the [[https://​www.hs-augsburg.de/​searchwing/​de/​seawatch-tests-2021/​|mission with Sea-Watch 4 with Philipp]].
  
 === Electronics / Board === === Electronics / Board ===
  
-Franc and Tim design ​a board for the antenna ground box.+Franc and Tim designed ​a board for the antenna ground box.
  
 {{ ::​sw-ags-pcb-v2.jpg |Antenna Ground Station PCB v1.0 with Hutschienenadapter}} {{ ::​sw-ags-pcb-v2.jpg |Antenna Ground Station PCB v1.0 with Hutschienenadapter}}
  
-**Fig. 4:** Antenna Ground Station ​v2 with PCB v1.0 with Hutschienenadapter+**Fig. 4:** Antenna Ground Station PCB v1.0 with Hutschienenadapter
  
 Figure 4 shows the antenna ground box PCB version 1.0. The design data is available at  Figure 4 shows the antenna ground box PCB version 1.0. The design data is available at 
Line 95: Line 99:
 [[https://​easyeda.com/​SearchWing/​antennagroundstation|Easyeda - Antenna Ground Station PCB Board]] [[https://​easyeda.com/​SearchWing/​antennagroundstation|Easyeda - Antenna Ground Station PCB Board]]
  
-The pcb board installed with Hutschiene inside the Spelsberg box.+The pcb board is installed with Hutschiene inside the Spelsberg box.
  
 {{ ::​sw-ags-box-v2.jpg | Antenna Ground Station v2 with PCB and Hutschiene}} {{ ::​sw-ags-box-v2.jpg | Antenna Ground Station v2 with PCB and Hutschiene}}
  • searchwing-antenna-ground-box.txt
  • Last modified: 2022/04/02 09:42
  • by beckmanf