Differences

This shows you the differences between two versions of the page.

--- searchwing-antenna-ground-box [2021/08/06 12:54]
beckmanf Update for Sea-Eye
+++ searchwing-antenna-ground-box [2022/04/02 09:42] (current)
beckmanf [Antenna ground box] add header datasheet
@@ Line 4: / Line 4: @@
   * [[https://www.taoglas.com/product/barracuda-omb-868-05f21-868mhz-omni-directional-outdoor-antenna|Taoglas Barracuda OMB.868.B05F21 868MHz 5dBi Omnidirectional Outdoor Antenna]]
-  * [[https://eckstein-shop.de/Pololu-5V-5A-Step-Down-Spannungsregler-D24V50F5| Pololu D24V50F5 5V DC/DC converter]] to provide power from 24V power input
+  * [[https://www.pololu.com/product/2851|Pololu D24V50F5 5V DC/DC converter]] to provide power from 24V power input
   * [[https://www.pusr.com/products/serial-to-ethernet-converter-modules-usr-tcp232-t2.html| USR-TCP232-T2 - UART to Ethernet Converter]]
   * [[https://www.gl-inet.com/products/gl-ar750/|GL-AR750]] access point to access mavlink via Wifi
-  * The [[searchwing-rf-antenne|RFD868+ Modem]].
+  * The [[searchwing-rf-antenne|RFD868+ Modem]]
+  * The Datasheet of the {{ ::ds_mpe_095.pdf |Angled Header}} available at [[https://www.reichelt.de/buchsenleisten-2-54-mm-2x10-gewinkelt-mpe-095-2-020-p119921.html?&nbc=1|Reichelt]].
 In addition it is possible to connect via the [[https://www.ftdichip.com/Support/Documents/DataSheets/Cables/DS_TTL-232R_CABLES.pdf|FTDI UART/USB]] cable with and without power from the 24V system. The router can also be connected with an ethernet cable to have wired access to the telemetry data.
+[[searchwing-antenna-ground-box#antenna_box_v2|Current Version V2]]
+==== Antenna Box V1 ====
 {{ ::basestationplatine.png?600 |}}
@@ Line 79: / Line 84: @@
 The image shows the installed SearchWing Antenna Box on the Alan Kurdi. The box contains a Wifi Access Point for a connection to the flight tablet computer. It is therefore recommended to operate the tablet in proximity to the box.
+==== Antenna Box V2 ====
+A new PCB board integrates the voltage regulator, RFD868+ modem, UART to Ethernet Converter on one board. Everything is now installed via "Hutschiene". This version was installed on the [[https://www.hs-augsburg.de/searchwing/de/seawatch-tests-2021/|mission with Sea-Watch 4 with Philipp]].
 === Electronics / Board ===
-Franc and Tim design a board for the antenna ground box.
+Franc and Tim designed a board for the antenna ground box.
+{{ ::sw-ags-pcb-v2.jpg |Antenna Ground Station PCB v1.0 with Hutschienenadapter}}
+**Fig. 4:** Antenna Ground Station PCB v1.0 with Hutschienenadapter
+Figure 4 shows the antenna ground box PCB version 1.0. The design data is available at
+[[https://easyeda.com/SearchWing/antennagroundstation|Easyeda - Antenna Ground Station PCB Board]]
+The pcb board is installed with Hutschiene inside the Spelsberg box.
+{{ ::sw-ags-box-v2.jpg | Antenna Ground Station v2 with PCB and Hutschiene}}
+**Fig. 5:** Antenna Ground Station v2 box with PCB and Hutschiene
+Figure 5 shows the Antenna Ground Station box V2 with PCB and Wifi AP on Hutschiene.
+{{ ::sw-ags-ap-hutschiene.jpg |}}
-[[https://easyeda.com/SearchWing/antennagroundstation||Easyeda - Antenna Ground Station Board]]
+**Fig. 6:** Hutschienenadapter mit Sekundenkleber an Wifi AP geklebt
+Figure 6 shows the Wifi Access Point glued with Sekundenkleber to the Hutschienenadapter.