Differences

This shows you the differences between two versions of the page.

--- searchwing-wing-servo [2020/02/01 16:40]
beckmanf created
+++ searchwing-wing-servo [2020/02/01 18:11]
beckmanf changed image descriptions
@@ Line 9: / Line 9: @@
   * [[https://www.digikey.de/product-detail/de/50-00601/839-1556-ND|Tensility M5 3-pin plug]], IP67, AWG26 (0.14mm2), 2.94€
   * [[https://www.digikey.de/product-detail/de/50-00604/839-1558-ND|Tensility M5 3-pin socket]], IP67, AWG26 (0.14mm2), 3.04€
-  * [[https://m-el.eu/details/61001|Muldental Schrumpfschlauch 1,2mm schwarz]]
+  * [[https://m-el.eu/details/61001|Muldental Schrumpfschlauch 1,2mm black]]
-  * [[https://m-el.eu/details/62106 |Muldental Schrumpfschlauch 4mm/1mm transparten mit Kleber]]
+  * [[https://m-el.eu/details/62106 |Muldental Schrumpfschlauch 4mm/1mm transparent mit Kleber]]
+==== Build instructions: M5 to Pixracer Cable ====
+The following image shows the final cable from the M5 Connector to the PixRacer. This cable is equipped with the socket connector - the plug is attached to the cable from the servo.
+{{:sw-m5-pixracer.jpg?600|M5 to Pixracer Cable}}
+The next image shows the solder view of the socket connector. The yellow cable has to be on the left side.
+{{:sw-servo-m5-to-pixracer.jpg?600|Solder view}}
+  * Cut 25mm of the transparent shrinking tube and put it on the cable
+  * Separate the yellow, red and brown cable for about 5cm
+  * Add about 5mm of the 1.2mm shrinking tube to the red and the brown cable.
+  * Move the shrinking tubes as far as possible from the solder spot to avoid accidental shrinking
+  * Remove the isolation for about 4mm and twist and tin the wires.
+  * Put the plug and the socket together and fix the screws to avoid mechanical deformation due to the solder process
+  * Fix the socket and the wire with a helping hand
+  * Solder the wire with a thin solder iron. Select a temperature of 270°C.
+The next image shows the socket after the solder process.
+{{:sw-m5-solder.jpg?600|Socket after soldering}}
+The next image shows the small shrinking tubes moved over the solder connections.
+{{:sw-m5-shrinking-tube.jpg?600|Socket with 1.2mm shrinking tubes}}
+  * Now shrink the black shrinking tubes with a heat gun. With the Heinel EL 1910 E heat gun select temperature "4" with maximum air speed.
+  * Move the 4mm/1mm transparent shrinking tube over the cable and the socket.
+  * Shrink with the heat gun and make sure that the hot glue seals the cable and the socket.
+  * Make sure that the screw can still be turned after shrinking and cooling.
+{{:sw-m5-final.jpg?600|M5 to Pixracer final socket}}
+Done!
+==== Build instructions: Servo to M5 cable ====
+The next image shows the final M5 connector which is connected to the cable from the servo. This cable has the M5 "plug". The M5 "socket" is on the cable to the PixRacer.
+{{:sw-m5-to-servo-final.jpg?600|Servo to M5 cable final}}
+The flow is the same as for the M5 to Pixracer cable, but the 4mm/1mm shrinking tube should be 40mm long. The next image shows the cable connection from the solder view. The yellow cable is on the right side.
+{{:sw-m5-to-servo-solder.jpg?600|Servo to M5 cable - solder view}}
+==== Final assembled M5 servo connector ====
+The next image shows the final, connected M5 connector.
+{{::sw-m5-all-final.jpg?600|Complete M5 Servo connector}}
-=== Building instructions ===