Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision Next revision Both sides next revision | ||
|
searchwing-wing-servo [2020/02/01 17:03] beckmanf added images and instructions |
searchwing-wing-servo [2020/02/01 18:11] beckmanf changed image descriptions |
||
|---|---|---|---|
| Line 12: | Line 12: | ||
| * [[https://m-el.eu/details/62106 |Muldental Schrumpfschlauch 4mm/1mm transparent mit Kleber]] | * [[https://m-el.eu/details/62106 |Muldental Schrumpfschlauch 4mm/1mm transparent mit Kleber]] | ||
| - | === Building instructions === | + | ==== Build instructions: M5 to Pixracer Cable ==== |
| The following image shows the final cable from the M5 Connector to the PixRacer. This cable is equipped with the socket connector - the plug is attached to the cable from the servo. | The following image shows the final cable from the M5 Connector to the PixRacer. This cable is equipped with the socket connector - the plug is attached to the cable from the servo. | ||
| Line 22: | Line 22: | ||
| {{:sw-servo-m5-to-pixracer.jpg?600|Solder view}} | {{:sw-servo-m5-to-pixracer.jpg?600|Solder view}} | ||
| - | * Cut 4cm of the transparent shrinking tube and put it on the cable | + | * Cut 25mm of the transparent shrinking tube and put it on the cable |
| - | * Add the metal screw to the cable | + | |
| * Separate the yellow, red and brown cable for about 5cm | * Separate the yellow, red and brown cable for about 5cm | ||
| - | * Add about 5mm of the 1.2mm shrinking tube to the red and the brown cable. | + | * Add about 5mm of the 1.2mm shrinking tube to the red and the brown cable. |
| + | * Move the shrinking tubes as far as possible from the solder spot to avoid accidental shrinking | ||
| * Remove the isolation for about 4mm and twist and tin the wires. | * Remove the isolation for about 4mm and twist and tin the wires. | ||
| + | * Put the plug and the socket together and fix the screws to avoid mechanical deformation due to the solder process | ||
| * Fix the socket and the wire with a helping hand | * Fix the socket and the wire with a helping hand | ||
| * Solder the wire with a thin solder iron. Select a temperature of 270°C. | * Solder the wire with a thin solder iron. Select a temperature of 270°C. | ||
| Line 43: | Line 44: | ||
| * Make sure that the screw can still be turned after shrinking and cooling. | * Make sure that the screw can still be turned after shrinking and cooling. | ||
| - | {{:sw-m5-final.jpg?600|Socket with 1.2mm shrinking tubes}} | + | {{:sw-m5-final.jpg?600|M5 to Pixracer final socket}} |
| Done! | Done! | ||
| + | |||
| + | ==== Build instructions: Servo to M5 cable ==== | ||
| + | |||
| + | The next image shows the final M5 connector which is connected to the cable from the servo. This cable has the M5 "plug". The M5 "socket" is on the cable to the PixRacer. | ||
| + | |||
| + | {{:sw-m5-to-servo-final.jpg?600|Servo to M5 cable final}} | ||
| + | |||
| + | The flow is the same as for the M5 to Pixracer cable, but the 4mm/1mm shrinking tube should be 40mm long. The next image shows the cable connection from the solder view. The yellow cable is on the right side. | ||
| + | |||
| + | {{:sw-m5-to-servo-solder.jpg?600|Servo to M5 cable - solder view}} | ||
| + | |||
| + | ==== Final assembled M5 servo connector ==== | ||
| + | |||
| + | The next image shows the final, connected M5 connector. | ||
| + | |||
| + | {{::sw-m5-all-final.jpg?600|Complete M5 Servo connector}} | ||