binaer_zu_7-segment_kodierer_code [Digitale Elektronik und Technische Informatik]

This page is read only. You can view the source, but not change it. Ask your administrator if you think this is wrong.
==== Binär zu 7-Segment Kodierer ====

<code vhdl bin2seg.vhd>
library ieee;
use ieee.std_logic_1164.all;
use ieee.numeric_std.all;

-- Translate a 4 Bit unsigned number to a 7-Segment Control
--           ---0---
--           |     |
--           5     1
--           |     |
--           ---6---
--           |     |
--           4     2
--           |     |
--           ---3---
-- Display the correct number for 0 - 9 and E for all other 
-- numbers which can be coded with 4 Bits (10-15).  

entity bin2seg is 
  port (
    number_i:   in  unsigned(3 downto 0);
    seg_o:      out std_ulogic_vector(6 downto 0)
  );
end; 

architecture rtl of bin2seg is
begin

  trans_p: process(number_i)
  begin
    case number_i is 
      when "0000" => seg_o <= "1000000";
      when "0001" => seg_o <= "1111001";
-- continue here...
      when others => seg_o <= "0000110";	
    end case;
  end process;
			   
end; -- architecture

</code> 


<code vhdl top.vhd>
library ieee;
use ieee.std_logic_1164.all;
use ieee.numeric_std.all;

entity top is 
  port (
    SW:         in  std_ulogic_vector(3 downto 0); -- Switches
    LEDR:       out std_ulogic_vector(9 downto 0); -- Red LEDs above switches
    HEX0:       out std_ulogic_vector(6 downto 0)
  );
end; 

architecture struct of top is

  component bin2seg is 
    port (
      number_i:       in  unsigned(3 downto 0);
      seg_o:          out std_ulogic_vector(6 downto 0)
    );
  end component;

begin
     
  bin2seg_i0 : bin2seg
    port map (
      number_i => unsigned(SW),
      seg_o    => HEX0);
      
  LEDR <= "0000000000";
                   			   
end; -- architecture

</code>

<code vhdl top_tb.vhd>
library ieee;
use ieee.std_logic_1164.all;
use ieee.numeric_std.all;

entity top_tb is
end; 

architecture beh of top_tb is

  component top
  port (
    SW:         in  std_ulogic_vector(3 downto 0); -- Switches
    LEDR:       out std_ulogic_vector(9 downto 0); -- Red LEDs above switches
    HEX0:       out std_ulogic_vector(6 downto 0) -- 7 Segment Display
    );
  end component;

  signal number              : unsigned(3 downto 0);
  signal switch              : std_ulogic_vector(3 downto 0);
  signal hex0                : std_ulogic_vector(6 downto 0);
  signal ledr                : std_ulogic_vector(9 downto 0);

begin
  
  top_i0 : top
    port map (
      SW                  => switch,
      LEDR                => ledr,
      HEX0                => hex0);
       
  switch <= std_ulogic_vector(number);
  
  process
  begin
    number <= "0000";
    wait for 10 us; 
    for i in 0 to 31 loop
      number <= number + 1;
      wait for 10 us;
    end loop;  
  end process; 

end; -- architecture
</code>