code_fuer_die_additionsschaltung [Digitale Elektronik und Technische Informatik]

This page is read only. You can view the source, but not change it. Ask your administrator if you think this is wrong.
=== Code für die Additionsschaltung ===

<code vhdl adder.vhd>
library ieee;
use ieee.std_logic_1164.all;
use ieee.numeric_std.all;

-- Add two numbers

entity adder is 
  port (
    a_i:      in unsigned(3 downto 0);
    b_i:      in unsigned(3 downto 0);
    sum_o:    out unsigned(3 downto 0)
  );
end; 

architecture rtl of adder is 
begin
  
  add_p : process(a_i, b_i)
  begin
    sum_o <= a_i + b_i; 
  end process add_p;
  			   
end; -- architecture

</code>

<code vhdl top.vhd>
library ieee;
use ieee.std_logic_1164.all;
use ieee.numeric_std.all;

entity top is 
  port (
    SW:         in  std_ulogic_vector(9 downto 0); -- Switches
    LEDR:       out std_ulogic_vector(9 downto 0); -- Red LEDs above switches
    HEX0:       out std_ulogic_vector(6 downto 0); -- 7 Segment Display
    HEX1:       out std_ulogic_vector(6 downto 0); -- 7 Segment Display
    HEX2:       out std_ulogic_vector(6 downto 0)  -- 7 Segment Display
  );
end; 

architecture struct of top is

  component bin2seg is 
    port (
      number_i:       in  unsigned(3 downto 0);
      seg_o:          out std_ulogic_vector(6 downto 0)
    );
  end component;

  component adder is 
    port (
      a_i:            in  unsigned(3 downto 0);
      b_i:            in  unsigned(3 downto 0);
      sum_o:          out unsigned(3 downto 0)
    );
  end component;
  
  signal a, b, sum : unsigned(3 downto 0);
  
begin
  
  a <= unsigned(SW(3 downto 0));
  b <= unsigned(SW(8 downto 5));
       
  bin2seg_i0 : bin2seg
    port map (
      number_i => a,
      seg_o    => HEX0);
      
  bin2seg_i1 : bin2seg
    port map (
      number_i => b,
      seg_o    => HEX1);
          
 -- Hier bin2seg für die Summe und adder einfügen    
      
  LEDR <= SW;
			   
end; -- architecture

</code>

<code vhdl top_tb.vhd>
library ieee;
use ieee.std_logic_1164.all;
use ieee.numeric_std.all;

entity top_tb is
end; 

architecture beh of top_tb is

  component top
  port (
    SW:         in  std_ulogic_vector(9 downto 0); -- Switches
    LEDR:       out std_ulogic_vector(9 downto 0); -- Red LEDs above switches
    HEX0:       out std_ulogic_vector(6 downto 0); -- 7 Segment Display
    HEX1:       out std_ulogic_vector(6 downto 0); -- 7 Segment Display
    HEX2:       out std_ulogic_vector(6 downto 0)  -- 7 Segment Display
    );
  end component;

  signal number1, number2    : unsigned(4 downto 0);
  signal switch              : std_ulogic_vector(9 downto 0);
  signal hex0, hex1, hex2    : std_ulogic_vector(6 downto 0);
  signal ledr                : std_ulogic_vector(9 downto 0);

begin
  
  top_i0 : top
    port map (
      SW                  => switch,
      LEDR                => ledr,
      HEX0                => hex0,
      HEX1                => hex1,
      HEX2                => hex2);
       
  switch(4 downto 0) <= std_ulogic_vector(number1);
  switch(9 downto 5) <= std_ulogic_vector(number2); 
  
  process
  begin
    number1 <= "00000";
    number2 <= "00000";
    wait for 10 us; 
    for i in 0 to 31 loop
      number1 <= number1 + 1;
      for v in 0 to 31 loop
        number2 <= number2 + 1;
        wait for 10 us;
      end loop;
    end loop;  
  end process; 

end; -- architecture

</code>