Differences
This shows you the differences between two versions of the page.
| Next revision | Previous revision Next revision Both sides next revision | ||
|
dataflash_log_download [2020/02/15 10:42] wf68spef created |
dataflash_log_download [2020/02/15 11:35] wf68spef |
||
|---|---|---|---|
| Line 13: | Line 13: | ||
| - Open http://192.168.4.1/update and flash the downloaded firmware | - Open http://192.168.4.1/update and flash the downloaded firmware | ||
| - Optinal: Set Params https://github.com/dogmaphobic/mavesp8266/blob/master/HTTP.md | - Optinal: Set Params https://github.com/dogmaphobic/mavesp8266/blob/master/HTTP.md | ||
| - | - Optinal: Set WIFI Channel via http://192.168.4.1/setparameters?channel=11 (Here Channel 11) | + | - Optinal: Set WIFI Channel via http://192.168.4.1/setparameters?channel=1 (Here Channel 1 - At HS Augsburg least occupied Channel) |
| - Optinal: Restart ESP as only then the new params will be used | - Optinal: Restart ESP as only then the new params will be used | ||
| - | - Open QGroundcontrol and download dataflash Log | + | |
| - | Test 14.2.2020 | + | Test 14.2.2020 - MAVEsp in AP Mode |
| - Qgroundcontrol Dailybuild 14.2.2020 | - Qgroundcontrol Dailybuild 14.2.2020 | ||
| - Mavesp Firmware 1.2.2 | - Mavesp Firmware 1.2.2 | ||
| + | - Login into pixracer WIFI which is provided by the ESP | ||
| + | - Open QGroundcontrol and download dataflash Log | ||
| - => Speed about 15-20kB/sec | - => Speed about 15-20kB/sec | ||
| - Estimated Time to Download One Flight: Pixracer creates 3.4 MB/Min => 204MB/h = 204MB/Flight => 204MB / 0,020MB/sec = 10200 Sec = 170 Min = ~3h | - Estimated Time to Download One Flight: Pixracer creates 3.4 MB/Min => 204MB/h = 204MB/Flight => 204MB / 0,020MB/sec = 10200 Sec = 170 Min = ~3h | ||
| + | |||
| + | Test 15.2.2020 - MAVEsp in Station Mode | ||
| + | |||
| + | - Login into pixracer WIFI which is provided by the ESP | ||
| + | - Set MAVEsp to Client / Station Mode: Mode = 1 . Be sure to type in the correct AP Name and Password. I tested by giving static IP | ||
| + | - Set Params via HTTP Interface: http://192.168.4.1/setparameters?mode=1&ssidsta=APNAME&pwdsta=PASSWORD&ipsta=192.168.8.44&gatewaysta=192.168.8.1&subnetsta=255.255.255.0&reboot=1 | ||
| + | - Start QGroundcontrol | ||
| + | - Connection should be established automatically | ||
| + | - Download dataflash Log | ||
| + | - Speed about 18kB/sec | ||
| === Method2: Download via MAVProxy to Pi === | === Method2: Download via MAVProxy to Pi === | ||
| Line 30: | Line 42: | ||
| - Wire RX / TX with the PI | - Wire RX / TX with the PI | ||
| - Install MAVProxy @ PI : sudo pip3 install mavproxy | - Install MAVProxy @ PI : sudo pip3 install mavproxy | ||
| - | - Set Telemetry Speed (115200 / 900000) via QGroundcontrol | + | - Set Telemetry Speed (115200 / 921600) via QGroundcontrol |
| - | - | + | - start pi<->pixracer connection : sudo mavproxy.py --master=/dev/ttyS0 --baudrate=921600 |
| - | RTL> Finished downloading 1.bin (473553 bytes 48 seconds, 9.8 kbyte/sec 143 retries) | + | - get log list : log list |
| + | - download log: log download <logid> <logname> | ||
| + | |||
| + | Test 15.2.2020 | ||
| + | - log download 1 1.bin | ||
| + | - => RTL> Finished downloading 1.bin (473553 bytes 48 seconds, 9.8 kbyte/sec 143 retries) | ||
| + | |||
| + | |||
| + | |||
| + | |||