[[dataflash_log_download]]

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision
Previous revision
Next revision Both sides next revision
dataflash_log_download [2020/02/15 11:34]
wf68spef
dataflash_log_download [2020/02/16 14:56]
wf68spef
Line 11: Line 11:
   - Download the latest firmware for mavesp: https://​github.com/​dogmaphobic/​mavesp8266   - Download the latest firmware for mavesp: https://​github.com/​dogmaphobic/​mavesp8266
   - Login into pixracer WIFI which is provided by the ESP   - Login into pixracer WIFI which is provided by the ESP
-  - Open http://​192.168.4.1/​update and flash the downloaded firmware +  - Open ''​http://​192.168.4.1/​update'' ​and flash the downloaded firmware 
-  - Optinal: Set Params https://​github.com/​dogmaphobic/​mavesp8266/​blob/​master/​HTTP.md +  - Optinal: Set Params ​''​https://​github.com/​dogmaphobic/​mavesp8266/​blob/​master/​HTTP.md''​ 
-  - Optinal: Set WIFI Channel via http://​192.168.4.1/​setparameters?​channel=1 ​ (Here Channel 1 - At HS Augsburg least occupied Channel)+  - Optinal: Set WIFI Channel via ''​http://​192.168.4.1/​setparameters?​channel=1'' ​ (Here Channel 1 - At HS Augsburg least occupied Channel)
   - Optinal: Restart ESP as only then the new params will be used   - Optinal: Restart ESP as only then the new params will be used
  
Line 30: Line 30:
   - Login into pixracer WIFI which is provided by the ESP   - Login into pixracer WIFI which is provided by the ESP
   - Set MAVEsp to Client / Station Mode: Mode = 1 . Be sure to type in the correct AP Name and Password. I tested by giving static IP   - Set MAVEsp to Client / Station Mode: Mode = 1 . Be sure to type in the correct AP Name and Password. I tested by giving static IP
-  - Set Params via HTTP Interface: http://​192.168.4.1/​setparameters?​mode=1&​ssidsta=APNAME&​pwdsta=PASSWORD&​ipsta=192.168.8.44&​gatewaysta=192.168.8.1&​subnetsta=255.255.255.0&​reboot=1+  - Set Params via HTTP Interface: ​''​http://​192.168.4.1/​setparameters?​mode=1&​ssidsta=APNAME&​pwdsta=PASSWORD&​ipsta=192.168.8.44&​gatewaysta=192.168.8.1&​subnetsta=255.255.255.0&​reboot=1''​
   - Start QGroundcontrol   - Start QGroundcontrol
   - Connection should be established automatically   - Connection should be established automatically
Line 41: Line 41:
  
   - Wire RX / TX with the PI    - Wire RX / TX with the PI 
-  - Install MAVProxy @ PI : sudo pip3 install mavproxy+  - Install MAVProxy @ PI : ''​sudo pip3 install mavproxy''​
   - Set Telemetry Speed (115200 / 921600) via QGroundcontrol   - Set Telemetry Speed (115200 / 921600) via QGroundcontrol
-  - start pi<​->​pixracer connection : sudo mavproxy.py --master=/​dev/​ttyS0 --baudrate=921600 +  - start pi<​->​pixracer connection : ''​sudo mavproxy.py --master=/​dev/​ttyS0 --baudrate=921600''​ 
-  - get log list : log list +  - get log list : ''​log list''​ 
-  - download log: log download <​logid>​ <logname>+  - download log: ''​log download <​logid>​ <filename>''​
  
 Test 15.2.2020 Test 15.2.2020
-  - log download 1 1.bin +  - ''​log download 1 1.bin''​ 
-  - RTL> Finished downloading 1.bin (473553 bytes 48 seconds, 9.8 kbyte/sec 143 retries)+  - => RTL> Finished downloading 1.bin (473553 bytes 48 seconds, 9.8 kbyte/sec 143 retries)
  
  
  • dataflash_log_download.txt
  • Last modified: 2022/05/31 18:11
  • by wf68spef