dtpr_v3_code_zaehler [Digitale Elektronik und Technische Informatik]

This page is read only. You can view the source, but not change it. Ask your administrator if you think this is wrong.
=== Code für den Zähler ===

<code vhdl counter.vhd>
library ieee;
use ieee.std_logic_1164.all;
use ieee.numeric_std.all;

-- First sequential circuit counts modulo 256
-- The circuit has two inputs, clk_i and reset_ni
-- and one output count_o. 
-- The function of the circuit is a counter which will increment by one
-- with each rising clock edge of clk_i
-- The counter uses flipflops with asynchronous reset for initializing
-- the flipflips and hence the counterstate to 0. Setting reset_ni to "0" will
-- reset the flipflops. 
-- The signal count_reg represents the Q outputs of the flipflops, while 
-- the signal new_count is connected the D inputs of the flipflops. 
-- The flipflops result from the description in the count_p process. 
-- The combinational logic which computes the new state of the flipflops
-- based on the current state is in new_count_p
-- The count_p process template is the way to infer flipflops. 

entity counter is 
  port (
    clk_i:      in std_ulogic;
    reset_ni:   in std_ulogic; 
    count_o:    out unsigned(7 downto 0)
  );
end; 

architecture rtl of counter is  
  signal count_reg, new_count : unsigned(7 downto 0);
begin

  -- Combinational process which computes the new state
  -- of the registers from the current state. This process will not
  -- infer registers but combinational logic 
  new_count_p : process(count_reg)
  begin
    -- !!!!! MODIFY THIS TO HAVE A COUNTER !!!!
    new_count <= not count_reg; 
  end process new_count_p;  

  -- The sequential process for flipflop instantiation
  -- All signal assignments in this process will result in flipflops.
  count_p : process (clk_i, reset_ni)
  begin
    if reset_ni = '0' then
      -- This is the asynchronous reset of the flipflops
      -- with negative logic, i.e. when the reset_ni is "0", then
      -- the flipflops are asynchronously reset. 
      count_reg <= "00000000";
    elsif rising_edge(clk_i) then
      -- Here the new state is assigned to the registers. 
      count_reg <= new_count; 
    end if; 
  end process count_p;  

  count_o <= count_reg;    
 			   
end; -- architecture
</code>


<code vhdl top.vhd>
library ieee;
use ieee.std_logic_1164.all;
use ieee.numeric_std.all;

entity top is 
  port (
    SW:         in  std_ulogic_vector(9 downto 0); -- Switches
    KEY:        in  std_ulogic_vector(3 downto 0); -- Keys
    LEDR:       out std_ulogic_vector(9 downto 0); -- Red LEDs above switches
    HEX0:       out std_ulogic_vector(6 downto 0); -- 7 Segment Display
    HEX1:       out std_ulogic_vector(6 downto 0); -- 7 Segment Display
    HEX2:       out std_ulogic_vector(6 downto 0)  -- 7 Segment Display
  );
end; 

architecture struct of top is

  component bin2seg is 
    port (
      number_i:       in  unsigned(3 downto 0);
      seg_o:          out std_ulogic_vector(6 downto 0)
    );
  end component;

  component counter is 
    port (
      clk_i:          in  std_ulogic;
      reset_ni:       in  std_ulogic; 
      count_o:        out unsigned(7 downto 0)
    );
  end component;
 
  signal count : unsigned(7 downto 0);

begin
       
  bin2seg_i0 : bin2seg
    port map (
      number_i => count(3 downto 0),
      seg_o    => HEX0);
      
  bin2seg_i1 : bin2seg
    port map (
      number_i => count(7 downto 4),
      seg_o    => HEX1);
          
  counter_i0 : counter
    port map (
      clk_i    => KEY(0),
      reset_ni => KEY(1),
      count_o  => count);
      
  LEDR(7 downto 0) <= std_ulogic_vector(count);
  LEDR(9 downto 8) <= "00"; 
  HEX2 <= "1111111";
			   
end; -- architecture
</code>

<code vhdl top_tb.vhd>
library ieee;
use ieee.std_logic_1164.all;
use ieee.numeric_std.all;

entity top_tb is
end; 

architecture beh of top_tb is

  component top 
  port (
    SW:         in  std_ulogic_vector(9 downto 0); -- Switches  
    KEY:        in  std_ulogic_vector(3 downto 0);
    LEDR:       out std_ulogic_vector(9 downto 0); -- Red LEDs above switches
    HEX0:       out std_ulogic_vector(6 downto 0); -- 7 Segment Display
    HEX1:       out std_ulogic_vector(6 downto 0); -- 7 Segment Display
    HEX2:       out std_ulogic_vector(6 downto 0)  -- 7 Segment Display
    );
  end component;

  signal clk, reset_n : std_ulogic;

  signal switch : std_ulogic_vector(9 downto 0);
  signal key    : std_ulogic_vector(3 downto 0);
  signal ledr   : std_ulogic_vector(9 downto 0);
  signal hex0, hex1, hex2 : std_ulogic_vector(6 downto 0); 

begin
  
  top_i0 : top
    port map (
      SW                  => switch,
      KEY                 => key,
      LEDR                => ledr,
      HEX0                => hex0,
      HEX1                => hex1,
      HEX2                => hex2);
           
  key(0) <= clk;
  key(1) <= reset_n; 
  key(3 downto 2) <= "00"; 
           
  clk_p : process
  begin
    clk <= '0';
    wait for 1 us;
    clk <= '1';
    wait for 1 us; 
  end process clk_p;

  reset_p : process
  begin
    reset_n <= '0';
    wait for 15500 ns; 
    reset_n <= '1';  
    wait; 
  end process reset_p;
   
  switch <= "0000000000";  

end; -- architecture

</code>