Differences
This shows you the differences between two versions of the page.
| Next revision | Previous revision Next revision Both sides next revision | ||
|
searchwing-antenna-ground-box [2020/02/14 14:42] beckmanf created |
searchwing-antenna-ground-box [2020/02/25 20:36] beckmanf added waveshare settings |
||
|---|---|---|---|
| Line 3: | Line 3: | ||
| The antenna ground box provides access to the antenna on the vessel from a laptop or tablet running QGroundControl. The station is composed of | The antenna ground box provides access to the antenna on the vessel from a laptop or tablet running QGroundControl. The station is composed of | ||
| - | * Taoglas Antenna | + | * [[https://www.taoglas.com/product/barracuda-omb-868-05f21-868mhz-omni-directional-outdoor-antenna|Taoglas Barracuda OMB.868.B05F21 868MHz 5dBi Omnidirectional Outdoor Antenna]] |
| - | * Polulu 5V DC/DC converter to provide power from 24V power input | + | * [[https://eckstein-shop.de/Pololu-5V-5A-Step-Down-Spannungsregler-D24V50F5| Pololu D24V50F5 5V DC/DC converter]] to provide power from 24V power input |
| - | * UART to Ethernet Converter | + | * [[https://eckstein-shop.de/Waveshare-UART-TTL-to-Ethernet-Converter-ETH-RJ45-Module-USR-TCP232-T2| Waveshare USR-TCP2323-T2 - UART to Ethernet Converter]] - [[https://www.waveshare.com/w/upload/b/be/UART_TO_ETH_User_Manual_V1.0.1.pdf| Datasheet]] |
| * [[https://www.gl-inet.com/products/gl-ar750/|GL-AR750]] access point to access mavlink via Wifi | * [[https://www.gl-inet.com/products/gl-ar750/|GL-AR750]] access point to access mavlink via Wifi | ||
| - | In addition it is possible to connect via the FTDI UART/USB cable with and without additional 24V power. The router can also be connected with an ethernet cable to have wired access to the telemetry data. | + | In addition it is possible to connect via the [[https://www.ftdichip.com/Support/Documents/DataSheets/Cables/DS_TTL-232R_CABLES.pdf|FTDI UART/USB]] cable with and without power from the 24V system. The router can also be connected with an ethernet cable to have wired access to the telemetry data. |
| + | |||
| + | {{ ::basestationplatine.png?600 |}} | ||
| === Connections === | === Connections === | ||
| - | * 24V power supply (max. 3A) | + | * 24V power supply from Ship (max. 3A / 6V-38V InputRange) |
| * Antenna cable with N connector for the Taoglas antenna | * Antenna cable with N connector for the Taoglas antenna | ||
| * Ethernet cable for wired access | * Ethernet cable for wired access | ||
| * FTDI UART/USB cable for direct wired access | * FTDI UART/USB cable for direct wired access | ||
| + | |||
| + | === Jumpers === | ||
| + | |||
| + | * Power Switch: Use Power from D24V50F5 DC/DC Converter (Jumper Left) or the USB Power via FTDI Cable (Jumper Right) | ||
| + | * Data Switch: Route the Telemetry RADIO TX/RX to Ethernet (Jumpers Left) or to the FTDI Cable (Jumpers Right) | ||
| + | |||
| + | === Mechanical === | ||
| + | |||
| + | The electronics is in a Spelsberg box with 300x300x180mm and pole mounting. | ||
| + | |||
| + | * [[https://www.spelsberg.de/industrieleergehaeuse/bis-40-x-50-cm-flexibel/70043301/|GEOS-L 3030-18-o Gehäuse]] mit | ||
| + | * GEOS MSS-30 Masthalterung mit Schraubschellenset SRS 60-90 und SRS 90-150 und einer | ||
| + | * GEOS-L EP-3030 Montageplatte mit (NOT USED) | ||
| + | * GEOS MH-22 Halterset (WRONG!!! This is too long and probably useless) | ||
| + | |||
| + | === Waveshare UART to Ethernet === | ||
| + | |||
| + | * User: SWing, Pass: SW018 | ||
| + | * IP: 192.168.8.100 | ||
| + | * MAC: 9C:A5:25:A0:48:B4 | ||
| + | |||
| + | Configuration: | ||
| + | |||
| + | * Baud Rate: 57600, 8 Databits, No Parity, 1 Stopbit | ||
| + | * Local Port: 14550 | ||
| + | * Remote Port Number: 14550 | ||
| + | * Work Mode: UDP Client | ||
| + | * Remote Server Addr: 192.168.8.255 | ||
| + | |||
| + | === Access Point === | ||
| + | |||
| + | * Type: GL-Inet AR750 | ||
| + | * SSID: SearchWing-AntBox | ||
| + | * Wifi Password: cassandra | ||
| + | * 5 GHz Channel 48, 2.4 GHz is OFF | ||
| + | * Router IP: 192.168.8.1 | ||
| + | * Admin Password: cassandra | ||
| + | |||
| + | The changes made from factory setting are: | ||
| + | * Wifi SSID, Passwords | ||
| + | * 2.4 GHz OFF | ||
| + | * Bind MAC from UART2ETH WaveShare to IP 192.168.8.100 | ||
| + | |||