Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision | ||
|
searchwing-firmware [2019/05/05 11:30] j0ge4622 Add parameter procedure |
searchwing-firmware [2019/05/05 11:57] j0ge4622 Update the failsafe params. |
||
|---|---|---|---|
| Line 55: | Line 55: | ||
| After the mag setup is changed, the mag sensors have to be calibrated. If you see a "Mag Inconsistent Error" in QGC, then this setup is wrong. | After the mag setup is changed, the mag sensors have to be calibrated. If you see a "Mag Inconsistent Error" in QGC, then this setup is wrong. | ||
| - | ===== Parameter procedure ===== | + | ===== Parameter ===== |
| + | |||
| + | ==== Procedure ==== | ||
| - Export parameter from QGC (.params file) | - Export parameter from QGC (.params file) | ||
| - Compare with the concurrent or for a new plane with an already existing file in [[https://gitlab.com/searchwing/operational/searchwing-config/tree/master/PX4|searchwing-config]], e.g. with git diff | - Compare with the concurrent or for a new plane with an already existing file in [[https://gitlab.com/searchwing/operational/searchwing-config/tree/master/PX4|searchwing-config]], e.g. with git diff | ||
| - Optional: Delete the not needed parameter and push the new file. | - Optional: Delete the not needed parameter and push the new file. | ||
| + | |||
| + | ==== Failsafes ==== | ||
| + | |||
| + | - Low Battery Failsafe: | ||
| + | - BAT_CRIT_THR = 0.1 (capacity [%]) | ||
| + | - BAT_EMERGEN_THR = 0.05 (capacity [%]) | ||
| + | - BAT_LOW_THR = 0.2 (capacity [%]) | ||
| + | - COM_LOW_BAT_ACT = 1 (return mode) | ||
| + | - RC Loss Failsafe: | ||
| + | - COM_RC_LOSS_T = 5 (time to detect RC-loss [s]) | ||
| + | - NAV_RCL_ACT = 0 (no action) | ||
| + | - Data Link Loss Failsafe: | ||
| + | - COM_DL_LOSS_T = 10 (time to detect datalink-loss [s]) | ||
| + | - NAV_DLL_ACT = 2 (return mode) | ||
| + | - Geofence Failsafe: | ||
| + | - GF_ACTION = 3 (return mode) | ||
| + | - GF_COUNT = -1 (counter limit to detect geofence breach) | ||
| + | - GF_MAX_HOR_DIST = 3000 (max horizontal distance home-plane [m]) | ||
| + | - GF_MAX_VER_DIST = 250 (max vertical distance home-plane [m]) | ||
| + | - Return Home Settings: | ||
| + | - RTL_DESCEND_ALT = 100 (altitude to loiter above home [m]) | ||
| + | - RTL_LAND_DELAY = -1 (no land, just loiter [s]) | ||
| + | - RTL_RETURN_ALT = 100 (altitude to flight to home [m]) | ||
| + | - RTL_TYPE = 0 (direkt path to home) | ||
| + | - Land Mode Settings: | ||
| + | - COM_DISARM_LAND = 1 (disarm after delay [s]) | ||
| + | - Position (GPS) Loss Failsafe: | ||
| + | - COM_POSCTL_NAVL = 1 (assume no RC → Land Mode with heigt, Termination without) | ||
| + | - COM_POS_FS_DELAY = 5 (time to detect GPS-loss [s]) | ||
| + | - NAV_GPSF_LT = 10 (loiter time to recover GPS [s]) | ||
| + | - NAV_GPSF_P = 0 (loiter pitch [deg]) | ||
| + | - NAV_GPSF_R = 15 (loiter roll [deg]) | ||
| + | - NAV_GPSF_TR = 0 (loiter thrust [%]) | ||
| + | - Mission Failsafe | ||
| + | - MIS_DIST_1WP = 1500 (max distance home-wp1 [m]) | ||
| + | - MIS_DIST_WPS = 2000 (max distance wp-wp [m]) | ||
| + | - Set both values to -1, if more than 10km are needed. | ||
| + | - Traffic Avoidance Failsafe | ||
| + | - NAV_TRAFF_AVOID = 2 (Return Mode) | ||
| ===== Releases ===== | ===== Releases ===== | ||