Differences

This shows you the differences between two versions of the page.

--- searchwing-minitalon-aufbau [2019/10/13 20:38]
j0ge4622
+++ searchwing-minitalon-aufbau [2020/02/21 15:04]
beckmanf added beams
@@ Line 31: / Line 31: @@
   * Flugzeug so auflegen, dass die Flügelvorderkante an den Anschlägen ist
   * Flugzeugneigung überprüfen, ansonsten Flugzeug anpassen
+==== Mini Talon Wings and Fuselage ====
+=== Main Wing ===
+  * Main beam: Outer diameter 10mm + 0.1mm, Inner diameter 8mm, Length 385mm
+  * Main beam, wing parts of : Outer diameter 7.8mm, length: 410mm
+  * Rear beam of main wing: Diameter 4mm, length: 735mm
+=== Fuselage beams ===
+Diameter: 4.1mm, length: 492mm
+The fuselage beams are the ones from the Mini Talon. Here is: [[:searchwing-fuselage-beams|How to glue the fuselage beams (milled frame)]]
+==== Power Module ====
+The power module provides the 5V DC/DC converters and the MOSFET switch. [[:searchwing-powermodule-in-fuselage|How to mount the power module in the fuselage]]
+==== Wing Servo Connection ====
+The servos in the left and right wing control the aileron. Here is:
+[[:searchwing-wing-servo|How to build the Wing servo connection]]
+==== Inner Frame ====
+The inner frame connects the Wingholme with the fuselage and it carries the PixRacer and the
+GPS Receiver. The frame is manufactured with 3D Print: [[:searchwing-inner-frame|How to build the inner frame]]
+==== Raspberry Pis incl. connection to Powermodule and PixRacer ====
+Two Raspberry Pis are mounted in the fuselage. Here is: [[:searchwing-pi-camera|How to mount the Pis and the Camera]]
+==== RFD868+ Telemetry Radio connection ====
+The RFD868+ long range telemetry is mounted on the right side of the fuselage. Therefore the modem is connected to the pixracer and power module just before glueing the left and right fuselage parts. Here is: [[:searchwing-rfd868-mount|How to mount the RFD868+ modem.]]
 ==== Connectors, Cables and Switches ====
@@ Line 83: / Line 118: @@
   * [[https://www.norcomp.net/series/m5-series-circular-connector|NorComp M5 3-pin connector]], IP67, Cable AWG26 - AWG28
-  * [[https://www.digikey.de/products/de?keywords=850-003-103RLU4|850-003-103RLU4]]
+  * [[https://www.digikey.de/products/de?keywords=850-003-103RLU4|850-003-103RLU4]] - 3 position, male connector, gold plated, 5.70€ each
- - 3 position, male connector, gold plated, 5.70€ each
+  * [[https://www.digikey.de/products/de?keywords=850-003-203RLU4|850-003-203RLU4]] - 3 position, female connector, gold plated, 6.00€
-  * [[https://www.digikey.de/products/de?keywords=850-003-203RLU4|850-003-203RLU4]]
- - 3 position, female connector, gold plated, 6.00€
 === Battery cable ===
@@ Line 92: / Line 125: @@
 Also for the battery a highly flexible cable should be used.
-  * [[https://kabel-me.eu/details/55043|Muldental 2.5mm2, 651x0.07mm, Silicon cable]]
+  * [[https://kabel-me.eu/details/55043|Muldental 2.5mm2, 651x0.07mm, Silicon cable]] 6.90€ for 4m (1.70€/m)
- - 6.90€ for 4m (1.70€/m)
+  * [[https://kabel-me.eu/details/58368D|XT60 with 30cm 2.5mm2 cable - prefconfigured]] 4.20€
-  * [[https://kabel-me.eu/details/58368D|XT60 with 30cm 2.5mm2 cable - prefconfigured]]
- - 4.20€
 === Power cable for Telemetry and Pi ===
@@ Line 119: / Line 150: @@
   * [[https://www.reichelt.de/wippschalter-2x-aus-schwarz-i-o-wippe-1932-3112-p154434.html|Marquardt 1932.3112 IP65 on/off switch]] 2.99€, 13g
-The switch can be connected with automotiv 6.3 x 0.8 mm connectors. Possible connector
+A smaller alternative with 10A max current is
-  * [[https://www.reichelt.de/flachsteckhuelse-6-3-x-0-8-mm-blau-100-stk-rnd-465-00065-p196125.html|6.3x0.8mm connector for 2.5mm2 cable diameter]]
+  * [[https://www.conrad.de/de/search.html?search=1588062|SCI switch from Conrad]]
-A smaller alternative with 10A max current, i.e. too small to switch directly is
+The (initial) on-resistance of 100mOhm of the Marquard switch will result in 10W Power consumption at 10A. A better approach is to use the switch to control the MOSFET. A schematic for the power switch including the MOSFET is here:
-  * [[https://www.conrad.de/de/search.html?search=1588062|SCI switch from Conrad]] with
+  * [[https://easyeda.com/editor#id=20aba1b75d594f2ea91e92b3c971e597|EasyEDA - SearchWingBatSwitch]]
-  * [[http://www.irf.com/product-info/datasheets/data/irf1405s.pdf|IRF1405 MOSFET]]
+  * [[https://www.digikey.de/product-detail/de/infineon-technologies/BSC010N04LSATMA1/BSC010N04LSATMA1CT-ND/4318664|BSC010N04 MOSFET Datasheet]]
-The (initial) on-resistance of 100mOhm of the Marquard switch will result in 10W Power consumption at 10A. A better approach is to use the switch to control the MOSFET also there.
 === Battery charging plug ===
@@ Line 281: / Line 310: @@
   * Akkuhalterung ca5mm mittig von der Rahmenvorderseite Richtung Rumpfspitze gemessen verkleben (Uhu Por) (auf Ausrichtung vorne/hinten (vorne breiten Wand, hinten Spannklettband) achten!)
-===== Kabelbaum Maße =====
+===== Kabelbaum =====
+==== Maße (alt) ====
 ^Src^Dst^Src - Stecker^Dst - Stecker^Länge [mm]^Kabelart^Querschnitt [mm²]^Anmerkungen|
@@ Line 296: / Line 327: @@
 |Pixracer (Servorail 2/3)|Servoverlängerung V-Tail L/R|3-pol Stecker|3-pol Stecker|200 (?)|3-polig| | |
 |ESC|Motor|MT60|MT60|350 (?)|3×1-polig|1|Schottverlängerung|
 ===== Montage der Mechanik und Elektronik =====