Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision Next revision Both sides next revision | ||
|
searchwing-minitalon-aufbau [2020/02/15 10:35] beckmanf added pi and camera |
searchwing-minitalon-aufbau [2020/02/21 15:04] beckmanf added beams |
||
|---|---|---|---|
| Line 32: | Line 32: | ||
| * Flugzeugneigung überprüfen, ansonsten Flugzeug anpassen | * Flugzeugneigung überprüfen, ansonsten Flugzeug anpassen | ||
| - | ==== Fuselage beams ==== | + | ==== Mini Talon Wings and Fuselage ==== |
| - | The fuselage beams are the ones from the Mini Talon. Here is: [[:searchwing-fuselage-beams|How to glue the fuselage beams]] | + | === Main Wing === |
| + | * Main beam: Outer diameter 10mm + 0.1mm, Inner diameter 8mm, Length 385mm | ||
| + | * Main beam, wing parts of : Outer diameter 7.8mm, length: 410mm | ||
| + | * Rear beam of main wing: Diameter 4mm, length: 735mm | ||
| + | |||
| + | === Fuselage beams === | ||
| + | |||
| + | Diameter: 4.1mm, length: 492mm | ||
| + | |||
| + | The fuselage beams are the ones from the Mini Talon. Here is: [[:searchwing-fuselage-beams|How to glue the fuselage beams (milled frame)]] | ||
| ==== Power Module ==== | ==== Power Module ==== | ||
| Line 53: | Line 62: | ||
| Two Raspberry Pis are mounted in the fuselage. Here is: [[:searchwing-pi-camera|How to mount the Pis and the Camera]] | Two Raspberry Pis are mounted in the fuselage. Here is: [[:searchwing-pi-camera|How to mount the Pis and the Camera]] | ||
| + | |||
| + | ==== RFD868+ Telemetry Radio connection ==== | ||
| + | |||
| + | The RFD868+ long range telemetry is mounted on the right side of the fuselage. Therefore the modem is connected to the pixracer and power module just before glueing the left and right fuselage parts. Here is: [[:searchwing-rfd868-mount|How to mount the RFD868+ modem.]] | ||
| ==== Connectors, Cables and Switches ==== | ==== Connectors, Cables and Switches ==== | ||
| Line 297: | Line 310: | ||
| * Akkuhalterung ca5mm mittig von der Rahmenvorderseite Richtung Rumpfspitze gemessen verkleben (Uhu Por) (auf Ausrichtung vorne/hinten (vorne breiten Wand, hinten Spannklettband) achten!) | * Akkuhalterung ca5mm mittig von der Rahmenvorderseite Richtung Rumpfspitze gemessen verkleben (Uhu Por) (auf Ausrichtung vorne/hinten (vorne breiten Wand, hinten Spannklettband) achten!) | ||
| - | ===== Kabelbaum Maße ===== | + | ===== Kabelbaum ===== |
| + | |||
| + | ==== Maße (alt) ==== | ||
| ^Src^Dst^Src - Stecker^Dst - Stecker^Länge [mm]^Kabelart^Querschnitt [mm²]^Anmerkungen| | ^Src^Dst^Src - Stecker^Dst - Stecker^Länge [mm]^Kabelart^Querschnitt [mm²]^Anmerkungen| | ||
| Line 312: | Line 327: | ||
| |Pixracer (Servorail 2/3)|Servoverlängerung V-Tail L/R|3-pol Stecker|3-pol Stecker|200 (?)|3-polig| | | | |Pixracer (Servorail 2/3)|Servoverlängerung V-Tail L/R|3-pol Stecker|3-pol Stecker|200 (?)|3-polig| | | | ||
| |ESC|Motor|MT60|MT60|350 (?)|3×1-polig|1|Schottverlängerung| | |ESC|Motor|MT60|MT60|350 (?)|3×1-polig|1|Schottverlängerung| | ||
| + | |||
| + | |||
| + | |||
| ===== Montage der Mechanik und Elektronik ===== | ===== Montage der Mechanik und Elektronik ===== | ||